Stenso - Hovedkatalog 2019

Limitations on Use Surface Finish Temperature : -40 bis +110 °C Velocity : reciprocating to 0.8 m/s Rmax Rz 2,5 µm 16,0 µm 16,0 µm 1,6 µm 10,0 µm 10,0 µm 0,4 µm 3,2 µm 3,2 µm Ra Rod diameter d Groove diameter D Groove flanks Part N°. d f8/h9 D1 +0,2 b D +0,2 E +0,2 Media for Use Mineral oil based pressure fluids, flame resistant fluids (HFA, HFB, HFC), non-polluting pressure fluids (Bio Oils). Further sizes and an extensive range of inch measurement diagrams available on request. 50,00 58,00 8,00 55,50 5,00 PW/B 50/58x5 70,00 82,20 12,00 76,00 7,20 PW/B 70/82,2x7,2 75,00 87,20 12,00 81,00 7,20 PW/B 75/81x7,2 80,00 92,50 12,00 86,00 7,20 PW/B 80/86x7,2 90,00 105,00 12,00 100,00 7,20 PW/B 90/100x7,2 115,00 127,00 11,00 119,00 7,20 PW/B 115/119x7,2 115,00 127,20 12,00 121,00 7,20 PW/B 115/121x7,2 120,00 132,20 12,00 126,00 7,20 PW/B 120/126x7,2 135,00 147,00 12,00 141,00 7,20 PW/B 135/141x7,2 140,00 155,00 14,00 150,00 9,50 PW/B 140/150x9,5 170,00 182,00 12,00 176,00 7,60 PW/B 170/176x7,6 170,00 185,00 14,00 175,00 10,20 PW/B 170/175x10,2 175,00 190,00 14,00 185,00 9,50 PW/B 175/185x9,5 185,00 200,00 14,00 195,00 9,50 PW/B 185/195x9,5 185,00 200,00 16,00 193,00 10,20 PW/B 185/193x10,2 192,00 207,00 12,00 199,00 8,00 PW/B 192/199x8 200,00 215,00 14,00 205,00 10,20 PW/B 200/205x10,2 210,00 225,00 16,00 218,00 10,20 PW/B 210x218x10,2 212,00 227,00 12,00 220,00 7,50 PW/B 212/220x7,5 212,00 232,00 18,00 225,50 12,50 PW/B 212/225,5x12,5 220,00 240,00 18,00 233,50 10,00 PW/B 220/233,5x10 220,00 240,00 18,00 233,50 12,50 PW/B 220/233,5x12,5 235,00 252,00 12,00 244,00 7,60 PW/B 235/244x7,6 260,00 280,00 15,00 270,00 10,20 PW/B 260/270x10,2 PW/B 160 Wiper Example for ordering Wipers: PW/B 200 / 215x14 Type Rod diameter d Groove diameter D Groove width WARNING vice conditions. In the event of a large duty cycle, pulsating operation and other complex operational conditions, simultaneous transgression of these values is not recommended. Due to a large variety of service conditions that may arise in course of actual use, the company does not take responsibility of or guarantee the functional accuracy of the individual components. Rights for changes are reserved. : Limits of application stated herein are standard values. They could be individually transgressed with due consideration to respective ser-