Stenso - Hovedkatalog 2019

Limitations on Use Media for Use Mineral oil based hydraulic oils, flame resistant pressure media and emulsions (HFA, HFB, HFC), Bio Oils. Maximum allowable operational pressure depending on the rubbing speed and temperature range of appli- cation as given below: Vmax [m/s] 0,50 0,15 25 MPa 40 MPa 16 MPa 25 MPa 10 Mpa 16 MPa -30 +60 -30 +80 -30 +110 Application Temperature [°C] Surface Finish Surfaces Rmax Rz 2,5 µm 10,0 µm 16,0 µm 1,6 µm 6,3 µm 10,0 µm 0,4 µm 1,6 µm 3,2 µm Ra Housting bore D Groove d Groove flanks or sides All types were not available at the time of printing. Please enquire in case of difficulty. Part N°. D H9 d h9 E +0,35 H +0,1 d1 h9 d2 h11 25,00 15,00 12,50 4,00 22,00 24,00 MD 25 25,00 17,00 10,00 4,00 22,00 24,00 MD 25 32,00 22,00 12,50 4,00 29,00 31,00 MD 32 32,00 24,00 10,00 4,00 29,00 31,00 MD 32 40,00 30,00 12,50 4,00 37,00 39,00 MD 40 40,00 32,00 10,00 4,00 37,00 39,00 MD 40 50,00 35,00 20,00 5,00 46,00 48,50 MD 50 50,00 40,00 12,50 4,00 47,00 49,00 MD 50 63,00 48,00 20,00 5,00 59,00 61,50 MD 63 63,00 53,00 12,50 4,00 60,00 62,00 MD 63 80,00 60,00 25,00 6,30 75,00 78,00 MD 80 80,00 65,00 20,00 5,00 76,00 78,50 MD 80 100,00 80,00 25,00 6,30 95,00 98,00 MD 100 100,00 85,00 20,00 5,00 96,00 98,50 MD 100 125,00 100,00 32,00 10,00 119,00 123,00 MD 125 125,00 105,00 25,00 6,30 120,00 123,00 MD 125 140,00 115,00 32,00 10,00 134,00 138,00 MD 140 140,00 120,00 25,00 6,30 135,00 138,00 MD 140 160,00 135,00 32,00 10,00 154,00 158,00 MD 160 160,00 140,00 25,00 6,30 155,00 158,00 MD 160 180,00 150,00 36,00 12,50 172,00 177,00 MD 180 200,00 170,00 36,00 12,50 192,00 197,00 MD 200 250,00 220,00 36,00 12,50 242,00 247,00 MD 250 320,00 290,00 36,00 12,50 312,00 317,00 MD 320 /15x12,5* /17x10* /22x12,5* /24x10* /30x12,5* /32x10* /35x20* /40x12,5* /48x20* /53x12,5* /60x25* /65x20* /80x25* /85x20* /100x32* /105x25* /115x32* /120x25* /135x32* /140x25* /150x36* /170x36* /220x36* /290x36* 26 Piston Seal Extensive range of inch measurement diagrams available on request. MD R = 0,4 for D < 100 R = 0,8 for D > 100 rounded and without burrs