Stenso - Hovedkatalog 2019

Surface Finish Surfaces Rz Ra 1,2 µm 6,3 µm 10,0 µm 0,3 µm 1,8 µm 3,2 µm Housing bore D Groove d Groove flanks Media for Use Mineral oil based hydraulic oils, flame resistant pressure media and emulsions (HFA, HFB, HFC). Bio Oils. Part N°. Part N°. D H10 D H10 d h10 d h10 E +0,3 E +0,3 20,00 10,00 9,30 CH3 20/10x9,3 22,00 12,00 9,30 CH3 22/12x9,3 25,00 15,00 9,30 CH3 25/15x9,3 28,00 18,00 9,30 CH3 28/18x9,3 30,00 20,00 9,30 CH3 30/20x9,3 32,00 20,00 10,90 CH3 32/20x10,9 35,00 23,00 10,90 CH3 35/23x10,9 36,00 24,00 10,90 CH3 36/24x10,9 40,00 25,00 11,50 CH3 40/25x11,50 42,00 27,00 11,50 CH3 42/27x11,5 45,00 30,00 11,50 CH3 45/30x11,5 50,00 35,00 11,50 CH3 50/35x11,5 55,00 40,00 11,50 CH3 55/40x11,5 56,00 41,00 11,50 CH3 56/41x11,5 60,00 45,00 11,50 CH3 60/45x11,5 63,00 48,00 13,00 CH3 63/48x13 70,00 50,00 15,20 CH3 70/50x15,2 80,00 60,00 15,20 CH3 80/60x15,2 90,00 70,00 21,20 CH3 90/70x21,2 100,00 80,00 21,20 CH3 100/80x21,2 110,00 90,00 21,20 CH3 110/90x21,2 115,00 95,00 21,20 CH3 115/95x21,2 125,00 100,00 25,80 CH3 125/100x25,8 140,00 115,00 25,80 CH3 140/115x25,8 150,00 120,00 29,00 CH3 150/129x29 160,00 130,00 29,00 CH3 160/130x29 180,00 150,00 31,50 CH3 180/150x31,5 200,00 170,00 33,50 CH3 200/170x33,5 225,00 195,00 33,50 CH3 225/195x33,5 220,00 190,00 33,50 CH3 220/190x33,5 250,00 220,00 33,50 CH3 250/220x33,5 275,00 245,00 33,50 CH3 275/245x33,5 300,00 270,00 33,50 CH3 300/270x33,5 CH 42 Limitations on Use Operating pressure Velocity Temperature : up to 40 MPa (400 bar) : reciprocating to max. 0.5 m/s : -30 to +110 °C (material NBR) : -10 to +150 °C ((material FPM) Single Acting Piston Seal Further sizes and imperial measurements as well as an extensive range of inch measurement diagrams available on request. Above sizes also available in FPM. Material Key: NBR V-ring FPM Example for ordering Piston Seal: CH3 36 / 24 x10,9 Type Bore diameter D Groove diameter d Groove width WARNING the event of a large duty cycle, pulsating operation and other complex operational conditions, simultaneous transgression of these values is not recommended. Due to a large variety of service conditions that may arise in course of actual use, the company does not take responsibility of or guarantee the functional accuracy of the individual components. Rights for changes are reserved. : Limits of application stated herein are standard values. They could be individually transgressed with due consideration to respective service conditions. In rounded