Stenso - Hovedkatalog 2019

Surface Finish Surfaces Rz 2,0 µm 6,3 µm 10,0 µm 0,3 µm 1,6 µm 3,2 µm Ra Housing bore D Grooved d Groove flanks Part N°. D H10 32,00 20,00 10,00 25,00 31,40 28,50 SAW 32/20x10 35,00 22,00 10,00 25,00 34,40 31,40 SAW 35/22x10 40,00 25,00 9,50 30,00 39,40 35,40 SAW 40/25x9,5 40,00 26,00 9,50 30,00 39,40 35,40 SAW 40/26x9,5 45,00 30,00 9,50 35,00 44,40 40,40 SAW 45/30x9,5 45,00 35,00 9,50 39,00 44,40 40,40 SAW 45/35x9,5 50,00 30,00 14,50 35,00 49,40 44,30 SAW 50/30x14,5 50,00 35,00 11,00 40,00 49,40 45,35 SAW 50/35x11 50,00 40,00 11,00 44,00 49,40 45,40 SAW 50/40x11 55,00 40,00 11,00 45,00 54,40 50,35 SAW 55/40x11 60,00 40,00 14,50 45,00 59,40 54,20 SAW 60/40x14,5 60,00 40,00 14,50 45,00 59,40 55,40* SAW 60/40x14,5* 60,00 45,00 11,00 50,00 59,40 54,20 SAW 60/45x11 60,00 45,00 11,00 50,00 59,40 55,40* SAW 60/45x11* 63,00 45,00 11,00 50,00 62,40 58,40 SAW 63/45x11 65,00 50,00 11,00 55,00 64,40 60,40 SAW 65/50x11 70,00 50,00 14,50 55,00 69,40 64,20 SAW 70/50x14,5 80,00 60,00 13,50 65,00 79,40 74,15 SAW 80/60x13,5 80,00 60,00 14,50 65,00 79,40 74,15 SAW 80/60x14,5 90,00 70,00 13,00 75,00 89,40 84,15 SAW 90/70x13 90,00 70,00 14,50 75,00 89,40 84,15 SAW 90/70x14,5 100,00 80,00 14,50 85,00 99,40 93,15 SAW 100/80x14,5 100,00 80,00 14,50 85,00 99,40 94,15* SAW 100/80x14,5* 110,00 95,00 13,00 100,00 109,40 103,10 SAW 110/95x13 120,00 100,00 14,50 105,00 119,40 113,10 SAW 120/100x14,5 120,00 100,00 14,50 105,00 119,40 114,10* SAW 120/100x14,5* d h10 E +0,2 G h8 F +0,1 D1 Media for Use Mineral oil based hydraulic oils, Bio Oils as well as flame resistant pressure liquids on request 44 Limitations on Use Operating pressure Velocity Ttemperature : up to 40 MPa (400 bar) : reciprocating up to 0.8 m/s : -40 to +110 °C Single Acting Piston Seal Example for ordering Piston Seal: SAW 60 / 40 x 14,5 Type Bore diameter D Groove diameter d Groove width WARNING vice conditions. In the event of a large duty cycle, pulsating operation and other complex operational conditions, simultaneous transgression of these values is not recommended. Due to a large variety of service conditions that may arise in course of actual use, the company does not take responsibility of or guarantee the functional accuracy of the individual components. Rights for changes are reserved. : Limits of application stated herein are standard values. They could be individually transgressed with due consideration to respective ser- SAW