Stenso - Hovedkatalog 2019

Part N° Part N° d f8/h9 d f8/h9 D H10 D H10 E +0,2 E +0,2 5,00 12,00 6,40 TGO 5/12x6,4 6,00 13,00 6,40 TGO 6/13x6,4 8,00 15,00 6,40 TGO 8/15x6,4 10,00 17,00 6,40 TGO 10/17x6,4 12,00 19,00 6,40 TGO 12/19x6,4 14,00 22,00 6,40 TGO 14/22x6,4 15,00 23,00 6,40 TGO 15/23x6,4 16,00 24,00 6,40 TGO 16/24x6,4 18,00 26,00 6,40 TGO 18/26x6,4 20,00 28,00 6,40 TGO 20/28x6,4 22,00 30,00 6,40 TGO 22/30x6,4 25,00 33,00 6,40 TGO 25/33x6,4 28,00 36,00 6,40 TGO 28/36x6,4 30,00 38,00 6,40 TGO 30/38x6,4 32,00 40,00 6,40 TGO 32/40x6,4 35,00 43,00 6,40 TGO 35/43x6,4 36,00 44,00 6,40 TGO 36/44x6,4 40,00 48,00 6,40 TGO 40/48x6,4 42,00 50,00 6,40 TGO 42/50x6,4 45,00 55,00 8,00 TGO 45/55x8 50,00 60,00 8,00 TGO 50/60x8 55,00 65,00 8,00 TGO 55/65x8 56,00 66,00 8,00 TGO 56/66x8 60,00 70,00 8,00 TGO 60/70x8 63,00 75,00 9,60 TGO 63/75x9,6 65,00 77,00 9,60 TGO 65/77x9,6 70,00 82,00 9,60 TGO 70/82x9,6 75,00 87,00 9,60 TGO 75/87x9,6 80,00 92,00 9,60 TGO 80/92x9,6 85,00 97,00 9,60 TGO 85/97x9,6 90,00 102,00 9,60 TGO 90/102x6,6 100,00 115,00 12,00 TGO 100/115x12 110,00 125,00 12,00 TGO 110/125x12 115,00 130,00 12,00 TGO 115/130x12 125,00 140,00 12,00 TGO 125/140x12 140,00 160,00 16,00 TGO 140/160x16 150,00 170,00 16,00 TGO 150/170x16 160,00 180,00 16,00 TGO 160/180x16 180,00 200,00 16,00 TGO 180/200x16 200,00 220,00 16,00 TGO 200/220x16 These sizes also available in FPM. Futher sizes/measurements and imperial sizes available on request . Rod Seal 92 Limitations on Use Diameter Clearance Operating pressure : up to 25 MPa (250 bar) Velocity : reciprocating to 0.5 m/s Temperature : -30 to +110 °C max. Diameter Clearancel S [mm] Max. Pressure [mm] 0,40 0,30 0,20 100 150 250 Surface Finish Surfaces Rz 2,0 µm 4,0 µm 8,0 µm 0,3 µm 0,8 µm 1,8 µm Ra Rod Diameter d Groove Diameter D Groove flanks Media for Use Mineral oil based hydraulic oils, flame resistant pressure media and emulsions (HFA, HFB, HFC), non-polluting pressure fluids (Bio Oils). Example for ordering Rod Seal: TGO 36 / 44 x 6,4N Type Rod diameter d Groove diameter D Material Groove width Material Key: NBR Standard FPM WARNING vice conditions. In the event of a large duty cycle, pulsating operation and other complex operational conditions, simultaneous transgression of these values is not recommended. Due to a large variety of service conditions that may arise in course of actual use, the company does not take responsibility of or guarantee the functional accuracy of the individual components. Rights for changes are reserved. : Limits of application stated herein are standard values. They could be individually transgressed with due consideration to respective ser- TGO